Insulation in Sierra Madre, CA
Spray foam insulation in Sierra Madre has to do two jobs at once: seal the envelope on homes that were never built for modern energy loads, and meet the fire-rated material specs this foothill city enforces because every block sits in a Very High Fire Hazard Severity Zone. Most of the housing stock here dates from the 1910s through the 1940s, and a lot of those Craftsman bungalows still have empty wall cavities or attic bays filled with nothing but sixty years of dust. Call Walt’s Insulation at (626) 606-2964 and you’ll get a live person, not a voicemail, 24/7.
Why Sierra Madre Homes Are Different
Sierra Madre sits where the San Gabriel Mountains drop into the San Gabriel Valley, and that geography drives everything about how we insulate here. The city is entirely inside a Wildland-Urban Interface zone, which means LA County code enforcement checks for fire-rated insulation materials at permit pull. A standard big-box fiberglass batt that passes inspection in Arcadia or Temple City often will not pass here. That reality lands on top of a housing stock dominated by pre-WWII Craftsman bungalows and early California vernacular homes built with balloon-frame construction, which left wall cavities and attic bays completely uninsulated. Homeowners in the historic preservation districts tend to resist open-wall replacement, so dense-pack blown-in cellulose or fiberglass through small-bore drill holes is usually the right retrofit method. The daily temperature swings here are sharp: south-facing hillsides radiate stored heat back into neighborhoods on summer evenings, pushing attic temperatures well above ambient, while cool mountain air drains down the canyon corridors at night. That wide thermal range makes radiant barrier and proper attic insulation pay for themselves faster in Sierra Madre than in flat valley addresses a few miles west.
Our Main Sierra Madre Services
Two jobs dominate the phones for Sierra Madre homeowners: attic insulation retrofits on old uninsulated houses, and crawl space encapsulation where foothill drainage and critter pressure meet. Here’s what each one involves.
Attic Insulation in Sierra Madre
Most Sierra Madre attics we open up are holding compacted 1920s-era rock wool or deteriorated compressed-paper fill sitting at near-zero effective R-value. Because the entire city falls inside the Very High Fire Hazard Severity Zone, the replacement product has to meet fire-rated specs that surprise homeowners who’ve gotten valley-city quotes before. We specify materials from Johns Manville and Rockwool that meet LA County WUI enforcement standards, and we air-seal the attic floor before we add insulation, because sealing and insulating together is what actually moves the energy bill. Attic Insulation in Sierra Madre covers this in depth.
Crawl Space Encapsulation & Vapor Barrier in Sierra Madre
Foothill drainage means Sierra Madre crawl spaces run damp, and damp crawl spaces feed mold, rot, and rodent activity under the house. Encapsulation seals the ground and foundation walls with a reinforced vapor barrier, which keeps moisture from migrating up into floor joists and living space. In this climate, the barrier also stops the nightly cool air that drains down the canyons from getting pulled into the home through floor gaps. Crawl Space Encapsulation & Vapor Barrier in Sierra Madre has the full breakdown.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Sierra Madre
Spray foam in Sierra Madre solves a problem this city has in spades: old balloon-frame houses with uninsulated wall cavities that leak air all day and all night. Closed-cell foam in particular does double duty here, because it hits the fire-rated spec that LA County’s WUI enforcement checks at permit pull while also sealing the building envelope far better than batts ever will. That matters on those hot foothill evenings when stored mountain heat pushes attic temperatures far above ambient, and on cool canyon nights when katabatic air drains down and finds every gap between board and beam. We install both open-cell and closed-cell systems from manufacturers including Johns Manville and Knauf, and we size every job to the specific cavity depth and fire-rating requirement this city demands. Spray Foam Insulation is our full service page.
Open-Cell Spray Foam
Signs you need it
Second-floor rooms over an uninsulated attic run ten degrees hotter than downstairs on summer afternoons, and the AC never seems to catch up.
What it costs in Sierra Madre
Open-cell spray foam in Sierra Madre typically runs $2.25 to $4.25 per board foot installed, with attic ceiling applications landing between $3,500 and $8,500 depending on square footage.
How we do it
We mask off the work area, spray the foam directly onto the underside of the roof deck or into open wall cavities, and leave it to cure fully before re-entering the space.
Closed-Cell Spray Foam
Signs you need it
You’re in a WUI-mandated retrofit, or you want the highest R-value per inch available because wall cavities in your older Sierra Madre home are shallow.
What it costs in Sierra Madre
Closed-cell foam runs $2.75 to $5.00 per board foot installed here, with whole-attic applications typically between $4,500 and $11,500 in Sierra Madre.
How we do it
We spray the two-part foam into the cavity or onto the deck, it expands to fill every seam and gap, and then we trim and inspect for full coverage before cleanup.
What Spray Foam Insulation Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Open-cell spray foam | $2.25 - $4.25 per board foot installed |
| Closed-cell spray foam | $2.75 - $5.00 per board foot installed |
| Attic ceiling spray foam | $3,500 - $11,500 installed |
Is spray foam worth it in Sierra Madre’s climate?
Yes, especially on homes with uninsulated walls and attic bays, because the foam seals air leaks while hitting the fire-rated spec this city enforces. It typically pays back fastest on south-facing and hillside lots.
Can you spray foam my older Sierra Madre home without opening walls?
For wall cavities, we use a small-bore injection approach that preserves original plaster and lath, which matters in the historic preservation districts. Attic and rim joist applications are fully non-invasive. Call (626) 606-2964 for a site read.
Blown-In Insulation in Sierra Madre
Blown-in insulation is the workhorse retrofit for Sierra Madre’s Craftsman-heavy housing stock, because it gets real R-value into wall cavities and attic bays without tearing out original plaster or opening up the envelope. Dense-pack cellulose or fiberglass, blown through small-bore holes, is exactly what the historic preservation culture here needs: effective, reversible, and quiet. The fire-rated spec matters here too, so we specify materials from CertainTeed and Knauf that meet the WUI requirement while delivering the thermal performance these wide-swinging foothill temperatures demand. Blown-In Insulation is our full service page.
Dense-Pack Wall Insulation
Signs you need it
Exterior walls feel cold to the touch in winter and radiate heat inward on summer evenings, and you can hear the street through them.
What it costs in Sierra Madre
Dense-pack wall insulation in Sierra Madre typically runs $1.75 to $3.50 per square foot of coverage, with whole-house retrofits landing between $2,800 and $7,500.
How we do it
We drill small access holes from the exterior or interior, blow the fill into each stud bay under pressure to prevent settling, then patch and restore the surface.
Blown-In Attic Top-Up
Signs you need it
Your attic has old, compacted fill sitting at near-zero effective R-value, or the ceiling temperature is noticeably warmer than the rest of the room on hot evenings.
What it costs in Sierra Madre
Blown-in attic top-up in Sierra Madre runs $1.25 to $2.75 per square foot, with typical 1,200-square-foot attics totaling $1,500 to $3,300.
How we do it
We air-seal the attic floor first, then blow fresh cellulose or fiberglass over the existing fill to reach the target R-value for this climate zone.
What Blown-In Insulation Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Dense-pack wall insulation | $1.75 - $3.50 per sq ft |
| Blown-in attic top-up | $1.25 - $2.75 per sq ft |
| Whole-house retrofit | $2,800 - $7,500 |
Will blown-in insulation settle in my Sierra Madre home?
Dense-pack cellulose and fiberglass are installed under pressure to prevent settling, and we verify cavity fill before patching. Properly installed, it holds its R-value for the life of the house. Call (626) 606-2964 for a free estimate.
Is blown-in insulation fire-rated for Sierra Madre’s WUI zone?
Yes, the products we specify from CertainTeed and Knauf meet the fire-rated material standards LA County checks at permit pull in the Very High Fire Hazard Severity Zone. We include the right product for your block on every quote.
Radiant Barrier Installation in Sierra Madre
Radiant barrier has outsized value in Sierra Madre because of where this city sits: south-facing foothill lots and mountain slopes soak up sun all day, then radiate that heat back into attics after dark. A foil radiant barrier stapled to the underside of the roof deck reflects that heat before it ever reaches your insulation or ductwork. The sharp diurnal swing here, warm days dropping into cool canyon nights, makes the barrier especially effective at keeping attic temperatures stable across the daily cycle. Radiant Barrier Installation is our full service page.
Attic Radiant Barrier
Signs you need it
Your upstairs rooms stay hot well after sunset, and the attic feels like an oven by late afternoon even when the outdoor air has started to cool.
What it costs in Sierra Madre
Attic radiant barrier in Sierra Madre runs $1.50 to $3.00 per square foot of deck area, with typical 1,200-square-foot attics totaling $1,800 to $3,600.
How we do it
We staple the perforated foil to the underside of the roof deck, leaving the required air gap at the ridge and eaves so ventilation keeps working.
Radiant Barrier & Ventilation
Signs you need it
The attic has poor airflow, and ridge or eave vents are undersized or blocked, which magnifies heat gain in the summer and moisture problems in the winter.
What it costs in Sierra Madre
Combined radiant barrier and ventilation upgrades in Sierra Madre run $2,000 to $5,500, depending on deck square footage and how many vents need adding.
How we do it
We install or upgrade ridge and eave vents, then add the radiant barrier beneath the deck, so reflected heat has somewhere to go instead of sitting in the attic.
What Radiant Barrier Installation Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Attic radiant barrier | $1.50 - $3.00 per sq ft of deck |
| Radiant barrier with ventilation | $2,000 - $5,500 |
| Typical 1,200 sq ft attic | $1,800 - $3,600 |
Does radiant barrier help in winter in Sierra Madre?
It helps less in winter than summer, but it still reduces heat loss through the roof on cold canyon nights. The bigger payoff here is summer, when reflected radiant heat keeps the attic 20 to 30 degrees cooler. Call (626) 606-2964.
Can you install radiant barrier in a historic Sierra Madre attic?
Yes, installation is completely non-invasive: we staple foil under the existing roof deck without disturbing original framing or finishes. It works in any attic with at least a few inches of clearance between deck and insulation.
Insulation Removal & Replacement in Sierra Madre
Insulation removal in Sierra Madre usually starts with a discovery: old rock wool or compressed-paper fill from the 1920s or 30s, flattened by decades of heat and moisture, sitting at near-zero effective R-value. Sometimes it’s worse, with rodent nests or water damage mixed in. The complication here, unique to this city, is the WUI fire-rating mandate: whatever goes back in has to meet the fire-rated spec, so the replacement product choice is not optional. Insulation Removal & Replacement is our full service page.
Contaminated Insulation Removal
Signs you need it
You find droppings, nesting material, or urine staining in the attic, or there’s a persistent musty odor coming down through the ceiling.
What it costs in Sierra Madre
Contaminated insulation removal in Sierra Madre runs $1.75 to $3.50 per square foot, with typical attics totaling $2,100 to $4,200 before replacement.
How we do it
We remove the contaminated material with HEPA-filtered vacuums, sanitize the deck and framing, and prepare the space for clean, fire-rated replacement insulation.
Vermiculite & Old Insulation Removal
Signs you need it
The attic contains loose vermiculite or deteriorated compressed-paper fill that cannot be brought up to current R-value by simply topping it up.
What it costs in Sierra Madre
Vermiculite and old insulation removal in Sierra Madre runs $2.00 to $4.00 per square foot, with typical attics totaling $2,400 to $4,800.
How we do it
We bag and remove the old material from the attic without spreading dust through the house, then assess the deck for any necessary repairs before new insulation goes in.
What Insulation Removal & Replacement Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Contaminated insulation removal | $1.75 - $3.50 per sq ft |
| Vermiculite / old insulation removal | $2.00 - $4.00 per sq ft |
| Typical attic full removal | $2,100 - $4,800 |
Do I have to remove old insulation before adding new?
Not always: if the existing fill is dry, clean, and not compressed to near-zero R-value, we can top it up. But if it’s contaminated, vermiculite, or collapsed, removal is the only way to restore real performance. Call (626) 606-2964.
Does replacement insulation have to be fire-rated in Sierra Madre?
Yes, because the whole city sits in the Very High Fire Hazard Severity Zone, LA County code enforcement checks the fire-rating on replacement products at permit pull. We specify the correct product for every job.
Attic Air Sealing in Sierra Madre
Air sealing matters disproportionately in Sierra Madre because the temperature swings are so wide: daytime heat pushes into the house through attic floor penetrations, and nighttime canyon air pulls conditioned air out the same way. On pre-WWII balloon-frame homes, the framing itself creates chimney-like paths from crawl space to attic that batts alone will never close. Sealing the attic floor before insulating is the single highest-leverage step for comfort and energy cost on these old foothill houses. Attic Air Sealing is our full service page.
Top Plate & Penetration Sealing
Signs you need it
Rooms get drafty when the wind picks up, and dust or insulation fibers appear around ceiling fixtures and wall-to-ceiling joints.
What it costs in Sierra Madre
Top plate and penetration sealing in Sierra Madre typically costs $800 to $2,200 for the average attic, depending on the number of penetrations and linear feet of top plate.
How we do it
We pull back existing insulation, seal every top plate joint and penetration with foam or caulk, then relay the insulation to full depth.
Can Light & Duct Boot Sealing
Signs you need it
Recessed lights are warm to the touch and drywall around them shows dust staining, or attic air blows through gaps where ducts pass through the ceiling.
What it costs in Sierra Madre
Can light and duct boot sealing in Sierra Madre runs $400 to $1,100 for a typical attic with 6 to 12 penetrations.
How we do it
We seal each can light housing with the appropriate fire-rated cover or box, and seal every duct boot to the drywall with mastic or foam.
What Attic Air Sealing Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Top plate & penetration sealing | $800 - $2,200 |
| Can light & duct boot sealing | $400 - $1,100 |
| Full attic air sealing | $1,200 - $3,300 |
Do I need air sealing before adding insulation?
Yes, sealing first is the rule: insulation slows heat transfer but does not stop air movement, so an unsealed attic lets conditioned air escape no matter how much fill you add. Call (626) 606-2964 for a check.
Is attic air sealing safe in an older Sierra Madre home?
Yes, sealing is completely non-invasive and works on any construction type, including balloon-frame Craftsman homes. It requires care around old wiring and fixtures, which is part of why training and background-checked technicians matter.
Wall Insulation in Sierra Madre
Wall insulation in Sierra Madre is usually a retrofit story: pre-WWII homes built with empty stud bays, and owners who don’t want original plaster torn open to fill them. Dense-pack injection through small-bore holes solves that, delivering real R-value without disturbing the historic fabric of the house. The fire-rating requirement applies to wall cavities here too, so the injection product we use meets the same WUI spec the attic materials do. Wall Insulation is our full service page.
Injection Foam Wall Insulation
Signs you need it
Rooms never hold temperature, exterior walls feel cold in winter and hot in summer, and there’s no insulation visible in the wall cavity from an outlet box.
What it costs in Sierra Madre
Injection foam wall insulation in Sierra Madre runs $3.00 to $5.50 per square foot of wall area, with whole-house retrofits typically $4,500 to $10,000.
How we do it
We inject expanding foam through small holes in the mortar joints or siding, fill each stud bay fully, then patch and color-match the surface.
Interior Wall Soundproofing
Signs you need it
Street noise from Sierra Madre Boulevard or neighboring canyon roads carries into bedrooms, or conversations travel through interior walls between rooms.
What it costs in Sierra Madre
Interior wall soundproofing in Sierra Madre runs $2.50 to $5.00 per square foot, with typical bedroom wall projects totaling $1,200 to $3,500.
How we do it
We dense-pack the wall cavity with sound-dampening material, then assess whether additional mass like a second drywall layer is needed for the target STC rating.
What Wall Insulation Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Injection foam wall insulation | $3.00 - $5.50 per sq ft |
| Interior wall soundproofing | $2.50 - $5.00 per sq ft |
| Whole-house wall retrofit | $4,500 - $10,000 |
Will wall insulation damage my historic plaster?
No, injection and dense-pack methods are specifically designed for occupied, finished homes: small holes, no gutting, no drywall replacement. The plaster and lath stay intact. Call (626) 606-2964 for an evaluation.
Does wall insulation have to be fire-rated in Sierra Madre?
Yes, the WUI fire-rating standard applies to wall cavity insulation in the Very High Fire Hazard Severity Zone, so we only specify products that meet the LA County code requirement at permit time.
Attic Cleaning & Rodent Proofing in Sierra Madre
Attic cleaning in Sierra Madre usually starts with what foothill wildlife leaves behind: rodents find their way into old attics through gaps in the eaves and vents, and they nest in the loose fill insulation that’s been sitting there for decades. The problem is worse here because the pre-WWII housing stock has more entry points and more undisturbed attic spaces than newer construction. Once the nesting and droppings are removed, the space has to be sealed so they can’t get back in, and that’s where rodent proofing and exclusion comes in. Attic Cleaning & Rodent Proofing is our full service page.
Attic Cleanout
Signs you need it
You hear scratching overhead at night, find droppings in the attic or around the ceiling hatch, or notice a persistent odor in upper rooms.
What it costs in Sierra Madre
Attic cleanout in Sierra Madre runs $1,500 to $4,000, depending on attic size and the amount of contaminated material to remove.
How we do it
We remove all debris, nesting material, and contaminated insulation with HEPA equipment, then vacuum the deck and framing clean.
Rodent Proofing & Exclusion
Signs you need it
You see gnaw marks, entry holes, or daylight through gaps at the eaves, gable vents, or where utility lines enter the attic.
What it costs in Sierra Madre
Rodent proofing and exclusion in Sierra Madre runs $800 to $2,500, depending on how many entry points need sealing and what materials are required.
How we do it
We seal every entry point with rodent-proof materials, install vent guards where needed, and verify the attic is fully closed off before finishing.
What Attic Cleaning & Rodent Proofing Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Attic cleanout | $1,500 - $4,000 |
| Rodent proofing & exclusion | $800 - $2,500 |
| Full cleanout + exclusion | $2,300 - $6,500 |
Do I need to replace insulation after rodent activity?
Usually yes: rodent urine and droppings contaminate the fill, and nesting compresses it past usefulness. Removal and replacement with clean, fire-rated insulation is the standard path. Call (626) 606-2964 for an assessment.
Can you guarantee rodents won’t come back?
Proper exclusion work, with every entry point sealed and vent guards installed, keeps them out permanently. The workmanship is covered by the Done Right Promise, and we stand behind the exclusion as long as the house is maintained.
Home Energy Audit in Sierra Madre
A home energy audit in Sierra Madre is one of the best dollars a homeowner here can spend, because the housing stock is old enough that most homes have never had a comprehensive look at where energy goes. The audit finds what the previous owners never knew: air leaks, missing insulation, faulty duct connections, and thermal bridging through old framing. In this climate, with the sharp daily temperature swings, the audit usually finds more savings potential than the homeowner expects. Home Energy Audit is our full service page.
Blower Door Test
Signs you need it
Rooms are drafty, the house feels like it’s leaking air, or energy bills are high without an obvious reason.
What it costs in Sierra Madre
A blower door test in Sierra Madre runs $300 to $600 as part of a full audit, or $200 to $350 standalone.
How we do it
We set up the fan in an exterior door, depressurize the house, and measure exactly how much air leaks through the envelope and where the biggest holes are.
Thermal Imaging Inspection
Signs you need it
Certain walls or ceilings feel cold in winter or hot in summer, and you suspect missing insulation or air gaps behind the finished surfaces.
What it costs in Sierra Madre
Thermal imaging inspection in Sierra Madre runs $250 to $500, and is often bundled with a blower door test in a full energy audit.
How we do it
We scan the interior and exterior surfaces with an infrared camera, which shows exactly where insulation is missing, compressed, or bypassed.
What Home Energy Audit Costs in Sierra Madre
| Item | Typical range in Sierra Madre |
|---|---|
| Blower door test | $300 - $600 |
| Thermal imaging inspection | $250 - $500 |
| Full home energy audit | $700 - $1,800 |
Is a home energy audit worth it for an older Sierra Madre home?
Yes, and often more than for newer houses, because pre-WWII construction typically has far more air leakage and missing insulation than anything built in the last thirty years. The audit shows exactly what to fix first. Call (626) 606-2964.
Does the audit include a written report?
Yes, every audit includes a written report with prioritized recommendations, so you can budget the fixes in order of payback. We don’t hold the results hostage: the report is yours.
Brands We Service in Sierra Madre
We install and service insulation from Johns Manville, Knauf, Rockwool, and CertainTeed, and our crews keep the common Sierra Madre parts and materials stocked locally. Turnaround on brand-specific product is usually same-week for this area. See our brands for the full list.
Pricing for Insulation in Sierra Madre, CA
| Service | Typical range in Sierra Madre |
|---|---|
| Open-cell spray foam | $2.25 - $4.25 per board foot installed |
| Closed-cell spray foam | $2.75 - $5.00 per board foot installed |
| Dense-pack wall insulation | $1.75 - $3.50 per sq ft |
| Blown-in attic top-up | $1.25 - $2.75 per sq ft |
| Attic radiant barrier | $1.50 - $3.00 per sq ft of deck |
| Contaminated insulation removal | $1.75 - $3.50 per sq ft |
| Attic air sealing | $1,200 - $3,300 for full attic |
| Wall injection foam | $3.00 - $5.50 per sq ft |
| Attic cleanout | $1,500 - $4,000 |
| Home energy audit | $700 - $1,800 |
| Rodent proofing & exclusion | $800 - $2,500 |
| Insulation replacement (full attic) | $2,100 - $6,500 |
What pushes prices up in Sierra Madre specifically: hard-to-access attics on steep foothill lots, the fire-rated material requirement that applies to every WUI property, and any contaminated or vermiculite removal that must happen before new insulation goes in. Every quote is upfront and line-itemed, and we honor the no-trip-charge policy inside the service county on every estimate.
Neighborhoods We Serve in Sierra Madre
We work across every part of Sierra Madre, from the downtown-adjacent blocks with the oldest Craftsmans to the hillside streets up toward the Angeles National Forest boundary. Response time is typically same-day or next-day for most of the city, depending on the job type.
- Downtown Sierra Madre
- Canyon Crest neighborhoods
- North Baldwin Avenue corridor
- Sierra Madre Canyon
- East Montecito foothills
Service Area - Cities Near Sierra Madre
Walt’s Insulation covers Sierra Madre and the surrounding foothill and valley communities. We also serve Arcadia, CA, San Gabriel, CA, Temple City, CA, and San Marino, CA, with the same live-answer phone line and Done Right Promise on every job.
Serving Sierra Madre, CA - Our Local Coverage Area
We’re based in the Sierra Madre area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Sierra Madre
We schedule same-day and next-day appointments across Sierra Madre, and because our techs work the foothill corridor regularly, we can often be on site within a few hours for emergency removal or assessment jobs. Call (626) 606-2964 and a live person picks up.
Most insulation retrofit work does not require a city permit, but the WUI fire-rating requirement is enforced at any point where a permit is pulled, such as a remodel or roof replacement. We specify compliant products on every job regardless of permit status.
Yes, estimates are free and we do not charge a trip fee inside the service county. You’ll get upfront line-item pricing and a written quote before any work is scheduled, plus a free second opinion on any other written estimate you’ve received.
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically same-day.
- 4You approve before work beginsNothing starts until you say go.
What Sierra Madre Customers Say
"Crawl space was wet every spring. They laid the heavy liner, sealed the vents, and put a dehumidifier down there. Floors are warm and the moisture meter he left reads fine now. He still answers when I text him a reading."
- Devon Pierce"Radiant barrier and new insulation in one visit. Walt explained what the foil actually does and what it does not, which nobody else bothered to. Electric bill in July was the lowest it has been in this house."
- Nadia Haddad"Walt came out himself, stuck his head in the attic, and told me I had about four inches where I needed fourteen. No sales pitch, just the number and what it would cost to fix it. Crew was here two days later."
- Carl Meadows